Translate

顯示具有 IR 標籤的文章。 顯示所有文章
顯示具有 IR 標籤的文章。 顯示所有文章

2023年8月9日 星期三

IR Loader Comparison | NUX Pulse vs TC Impulse vs Darkglass Element

IR Loader Comparison | NUX Pulse vs TC Impulse vs Darkglass Element


隨著Ampless的應用場景越來越普遍,以及Line In錄音的便利性,這年頭身為吉他手對於Amp Modeler / Profiler,以及IR Loader 等產品可說是家常便飯的話題了。
喜歡使用單顆效果器的吉他手,在擁有自己喜歡的Preamp或者Drive / Distortion效果器後,為了解決Ampless使用場景,除了選擇Stomp-box Modeler外,IR Loader就成了另一種主流選擇。


今天就讓我們來聊聊市面上三款IR Loader產品,以及我測試後的使用心得吧。

我先將這三款做了一份對照表,讓看官們可以先有一個參數上的基本比較與概念。

如果不想看太多文字的,也可以先看一下對比評測影片:
IR Loader Comparison | NUX Pulse vs DARKGLASS Element vs TC Pulse

1. Darkglass Element

首先讓我們來看一下DG的Element,這一款嚴格來說,不能算效果器。
因為 (1)沒有Footswitch可以針對現場演出使用。 (2)輸出為兩個3.5mm PHONES OUT,並非樂器常用的1/4" (6.35mm)接口。

Element的設計比較偏向 (1)帶有IR Loader的錄音介面 (2)兩個獨立輸出的耳機接口,方便樂團樂手便攜錄音時,一起監聽使用。 (3)編輯軟體帶有Amp Sim。


將Element接上電腦的USB口後,Darkglass Suite編輯軟體針對Element提供Noise Gate、Amp、Cab(Impulse Response)、EQ等4個效果模塊。 當然你可以將Gate、Amp、EQ等模塊給關閉,只使用IR。
從上位機軟體的設計,你就可以理解Element就是一個專為貝斯手以及吉他手所設計錄音介面。

拆解後,Element使用的主DSP是 NXP RT1021,運算力為 400MHz,算是很強的平台了。
原本推估IR的實時運算解析度應該可以跑到1024點,但實測對比後,估計是512點。 因為其低頻的動態反應不如NUX Pulse。
或許是將運算力分給了其他效果模塊。

想了解更多IR運算的原理與細節,歡迎回顧我們以前寫的文章:


2. TC Impulse

TC這款Impulse有幾個賣點,原廠搭配Celestion的IR,算是找了名牌IR做背書。 體積小,操作簡單直覺,帶有一個bit風格的螢幕,檔案名稱一目瞭然。
但我覺得比較可惜的是:(1)沒有耳機輸出口可以做靜音練習。 (2)不支持USB Audio Stream,所以不能當錄音介面。


TC Impulse採用的主芯片是ST的STM32F732,運算力為216MHz。 所以注定了IR實時運算力只能到512點了。 而實測下來也確實是如此,聲音的清晰度以及低頻張力,略遜NUX Pulse的1024點。

3. NUX Pulse


NUX Pulse這款minii Pedal的特色就是體積小,操作簡單直覺,所見即所得。 分EG Cab、Bass Cab、AG IR等三種模式,這三種模式個有8個default IR檔。 現場操作除了LEVEL以外,有個Space的旋鈕設計來調整現場的空間感,且可以透過長按踩釘來 開/關 Space,算是相當貼心。
另外側邊有3.5mm耳機輸出支持『靜音練習』。 IR實時運算力解析度達1024點。 USB支持錄音介面功能。


缺點就是沒有屏幕顯示,所以當你將原本的slot替換成第三方IR時,你得自己記得對應的slot放的是什麼。

拆解後,使用的DSP是NXP RT1061,運算力可達600MHz,是這三款產品中,運算力最強的平台。 確實可以將IR實時運算跑到1024點。

NUX Pulse (NSS-4) IR Loader Review


相信以上的評測跟對比,讓你對這類型產品有更深層的認識。
青菜蘿蔔各有所好,祝你找到喜愛的產品。


感蝦支持~


2023年7月27日 星期四

Mighty Powerhouse | NUX MIGHTY LITE BT MKII

Mighty Powerhouse | NUX MIGHTY LITE BT MKII


疫情期間,居家隔離,遠端辦公,讓人們多了些時間待在家裡,也讓吉他手們多了點練琴的時間,而由於都市人都住在公寓裡,桌上型音箱逐漸成為了練習音箱的主流。

During the pandemic, quarantine and remote offices allowed people to spend more time at home and also allowed guitarists to spend more time practicing. Since urbanites live in apartments, desktop speakers have gradually become mainstream practice amplifiers.

今天讓我們來聊聊 小瓦數桌上型音箱 NUX MIGHTY LITE BT MKII

Today let's talk about the small-wattage desktop amplifier NUX MIGHTY LITE BT MKII.


Portable Desktop Modeling Amp with IRs.


這款音箱,有別於其他桌上型小瓦數音箱的特點在於IR。
關於IR的詳細介紹,不熟悉的朋友可以參考這裡 ➫ 

The feature of this amp, which is different from other desktop small-wattage speakers, is IR.
For a detailed introduction to IR, friends who are not familiar with it can refer to here ➫
Amp Modeling & IR

MKII 跟上一代對比,主要更新了 Amp Modeling (TSAC-HD算法)跟 IR。
IR的部分包含了 (1)電吉他Cab IR , (2)電貝斯Cab IR , (3)木吉他線圈拾音器IR 。
而且還可以讓用戶通過Mighty Editor™電腦端編輯軟體load第三方IR檔。
(廠家預設36個,用戶slot共18個。)

Compared with the previous generation, MKII mainly updated Amp Modeling (TSAC-HD algorithm) and IR.
The IR part includes (1) Electric Guitar Cab IR, (2) Electric Bass Cab IR, (3) Acoustic Guitar Magnetic Pickup IR.
And it also allows users to load third-party IR files through the Mighty Editor™ computer editing software.
(The factory defaults to 34 slots, and the user slots total 20.)


NUX Mighty Lite BT MKII test by Jimmy Lin (No Talking)

I/O and other features.


3" 喇叭搭配低音反射孔
9V外正內負供電(附變壓器)或 6 x AA 電池
USB Audio
Phones Out & AUX In
鼓機
藍牙音頻
藍牙MIDI (APP)

3" Speaker with Bass Port Tube
9V DC/Battery( 6 x AA)  120mA (Adaptor included)
USB Audio
Phones Out & AUX In
Drum Machine
Bluetooth Audio
Bluetooth MIDI (APP)



Bluetooth Audio Setup 

將支持藍牙的移動設備連接至 MIGHTY LITE BT MKII 的藍牙音頻時,BLUETOOTH 指示燈將呈“藍色”亮起。(如果未連接,BLUETOOTH 指示燈將閃爍“藍色”。)

When connecting a Bluetooth enabled mobile device to the MIGHTY LITE BT MKII’s Bluetooth audio, the BLUETOOTH indicator will turn on “Blue”. 
(If not connected, the BLUETOOTH indicator will flash “Blue”.)




操作:您可以在手機“設定”中連接藍牙音頻,通過MIGHTY LITE BT MKII播放音頻。 點擊手機上的“設定”。 進入“藍牙”,選擇“NUX NGA-3BT”,當您連接MIGHTY LITE BT MKII的藍牙音頻時,您會聽到連接聲音。

Operation: You can connect Bluetooth Audio from “Settings” on the mobile phone to play audio through the MIGHTY LITE BT MKII. Click “Settings” on the mobile phone. Enter “Bluetooth”, and choose “NUX NGA-3BT”, while you connect MIGHTY LITE BT MKII’s Bluetooth audio, you will hear a connection sound.

如果您想斷開 MIGHTY LITE BT MKII 的連接,只需按住 PRESET 按鈕/指示燈即可斷開連接。 然後您可以手動連接到 MIGHTY LITE BT MKII。

If you wish to disconnect the MIGHTY LITE BT MKII, just press and hold the PRESET button/indicator to disconnect. Then you can connect to MIGHTY LITE BT MKII manually.


Bluetooth MIDI (APP) Setup



操作:在手機上啟動MightyAmp™ APP,按“設置”選擇“當前設備”為“MIGHTY LITE BT MKII”,然後“單擊掃描設備”。 該APP將找到“MIGHTY LITE BT MKII”。 現在選擇它,APP將與設備連接。

Operation: Launch the MightyAmp™ APP on your mobile phone, and press “Settings” to choose “Current Amp” as “MIGHTY LITE BT MKII”, then “Click to Scan Devices”. The APP will find “MIGHTY LITE BT MKII”. Now select it, and the APP will connect with the device.

注意:該APP使用藍牙 MIDI 與設備通信。

NOTE: The APP uses Bluetooth MIDI to communicate with the device.

注意:對於 Android 操作系統,您可能需要打開 GPS 權限。
隱私說明:請注意,我們不會使用您的任何 GPS 數據。 Android 要求所有掃描藍牙設備的移動應用程序都必須在清單文件中請求權限。 需要此 LOCATION 權限,因為可以通過查看附近的 BTLE 設備來猜測 Android 設備的位置。 請參閱 Android 開發者以獲取更多信息。

NOTE: For Android OS, you may need to turn on GPS permission.
PRIVACY NOTE: Please note that we do not use any of your GPS data. It is required by Android that all mobile applications that scan for Bluetooth devices must request permission in the manifest file. This LOCATION permission is required because it may be possible to guess the location of an Android device by seeing which BTLE devices are nearby. Please refer to Android Developer for more information.


Mighty Lite BT MKⅡ | 山口和也


Tone Tweaking | 音色調整


(0)
關於Modeling Amp,跟Modeler一樣,調整音色的第一步:
請bypass所有的效果模塊,設定乾信號的音量達到你想要的程度。 (將Patch Level推子從最小刻度開始調整到你覺得音量足夠大且不會傷害你的耳朵、舒服為準。)在Mighty Light BT MKII上,我通常將Patch Level設為『0』。
然後才開始加入效果模塊,如AMP、IR、動態效果(Compressor、Pre-efx)及其他效果...等等。

For the Modeling Amp, same as modelers, in the 1st step for "TONE TWEAKING": 
Please bypass all the effect blocks, and set the dry signal volume as you want. (Tweak the Patch Level slider from minimum to the desired comfortable volume so that you feel it loud enough and it won't hurt your ears.) On the Mighty Light BT MKII, I usually set the Patch Level to "0".
Then start to add the blocks like AMP, IR, dynamic effect, ...etc.

(1)
我第一個會添加的效果模塊是AMP(與此同時,我會加入對應的“箱體 IR”),所以一開始我必須決定在這個Preset中,我想要的音箱類別。
讓我們來對音箱做個分類吧: 清音 (Fender Clean), 過載邊緣 (Vox Drive), 英式過載 (Marshall Crunch), 失真 (Modern Distortion)。
簡稱為 F / V / M / Modern Dist。

The first block I will add is AMP (add the related “CAB / IR” at the same time), so in the beginning, I have to decide the Amp Category I want for the Preset. 
Let's classify the amps as Cleanish (Fender Clean), Edge-of-Breakup (VOX Drive), British-Crunch (Marshall Crunch), and Lead-Distortion (Modern Distortion).
We can simply call them F / V / M / Modern Dist.



在Mighty Lite BT MKII裡面,清音類型的音箱有 Roland JC-120, Fender Deluxe Reverb,以及Fender Super Reverb。
我喜歡的清音音箱模型為SUPER RVB。

In the Mighty Lite BT MKII, the cleanish amps are Roland JC-120, Fender Deluxe Reverb, and Fender Super Reverb.
My favorite clean amp is SUPER RVB.



過載邊緣的音箱有: Fender Bassman, Fender Tweed Deluxe, HIWATT DR103, Mesa Boogie Mark I, VOX AC30, Dr. Z MAZ 38。

The Edge-of-Breakup amps are Fender Bassman, Fender Tweed Deluxe, HIWATT DR103, Mesa Boogie Mark I, VOX AC30, and Dr. Z MAZ 38.



英式過載音箱有: Marshall Super 1959, Marshall JTM45, Marshall JCM 800, Marshall 1987X。

The British-Crunch amps are Marshall Super 1959, Marshall JTM45, Marshall JCM 800, and Marshall 1987X.



失真音箱有:Soldano SLO100, Friedman BE100, Mesa Boogie Dual Rectifier, Diezel VH4。

The Lead-Distortion amps are Soldano SLO100, Friedman BE100, Mesa Boogie Dual Rectifier, and Diezel VH4.

*All of the brand and model names mentioned on this page are Trademarks of their respective owners, which are in no way associated or affiliated with NUX Effects and Cherub Technology CO. LTD.


在選定音箱模型後,我會執行以下動作:
將音箱模型的EQ調平,再將音箱模型的 GAIN 與 LEVEL 調平與 乾信號音量相當。 
進行EQ的細調節,依序調節BASS(低頻), MID(中頻), TREBLE(高頻), PRESENCE(臨場度,也可稱為超高頻)。
調節低頻時,我會彈奏第五弦及第六弦空弦音,並將BASS旋鈕從最小值開始轉大直到低頻臨界點。 與此同時,你會聽到低頻忽然衝出來,這就是臨界點。
同樣的方式調節中頻。 調節中頻時,我會彈奏第三弦及第四弦空弦音,並將MID旋鈕從最小值開始轉大直到中頻臨界點。 與此同時,你會聽到中頻忽然衝出來。
同樣的方式調節高頻。 調節高頻時,我會彈奏第一弦及第二弦空弦音,並將TREBLE旋鈕從最小值開始轉大直到高頻臨界點。 與此同時,你會聽到高頻忽然衝出來。
同樣的方式調節臨場度。 調節臨場度時,我會彈奏第一弦及第二弦空弦音,並將PRESENCE旋鈕從最小值開始轉大直到臨場度臨界點。 與此同時,你會聽到臨場度超高頻忽然衝出來。
*註記:VOX類型的音箱模型使用的是CUT旋鈕,我會逆時針方向調節他。

然後我會再次調節GAIN與LEVEL,尋找出音箱模型的甜蜜點。
最後一步則是選擇箱體IR。

After I chose the amp model, what I will do:
Set the EQ flat, then adjust the GAIN and LEVEL as balanced as the flat dry signal.
Dig the EQ according to BASS, MID, TREBLE, and PRESENCE. 
While I dig the bass, I will play the 5th & 6th open strings and tweak the BASS knob from minimum to the BASS critical point. In the meantime, you will hear the BASS frequency volume increase quickly. 
Same as the MID, I will play the 3rd & 4th open strings and tweak the MID knob from minimum to the MIDDLE critical point. In the meantime, you will hear the MIDDLE frequency volume increase quickly. 
Same as the TREBLE, I will play the 1st & 2nd open strings and tweak the TREBLE knob from minimum to the TREBLE critical point. In the meantime, you will hear the TREBLE frequency volume increase quickly. 
Same as the PRESENCE, I will play the 1st & 2nd open strings and tweak the PRESENCE knob from minimum to the PRESENCE critical point. In the meantime, you will hear the PRESENCE volume increase quickly.
*NOTE: The VOX-style amp uses a CUT knob, I will tweak it counterclockwise.

Then I will adjust the GAIN and LEVEL again, and find the sweet spot for the AMP model.
In the last step, choose the CAB IR.

(2)
Dynamic effects: Pre-efx, Cmp (Gate in case.) | 動態效果: 前級過載、壓縮 (必要時加入『降噪』)

依據需求,我會在『清音音箱模型』加入Compressor(壓縮)效果;在『過載邊緣音箱』或『英式過載音箱』加入Overdrive(過載)效果。 有時候在『失真音箱』加入Compressor(壓縮)可以增加高把位音符的增益。
如果增益太多伴隨著噪聲,那麼適當加入Noise Gate(降噪)。

Depending on the need, I will add a compressor for the cleanish amp, an overdrive pedal for the Edge-of-Breakup amp even the British-Crunch amp. Sometimes you can add a compressor for the Lead-Distortion amp to enhance the gain of high-position notes.
If there is too much gain with noise, add "Noise Gate" just in case.

(3)
Time-based or Modulation | 時間系或調變效果

這裡我列舉了我常用的MOD模型。 以Chorus來說,我經常加入到『清音音箱』來彈奏流行曲的分解和弦伴奏。 至於Phaser或Tremolo,我喜歡放到『英式過載音箱』之前,讓他聽起來更肥或者更有立體感。

Here I listed the MOD models I use mostly. For the Chorus, I usually add it to a cleanish amp model and play the arpeggios for pop accompaniment. For Phaser and Tremolo, I would like to put it before the British-Crunch amp to make it sound fatter or stereo-like.


Delay(延遲)效果,有好幾種類型,針對延遲的音色與時長來使用是一種進階的技巧,這裡我不會去談論。 如果你對這個話題感興趣的話,請參考我之前的文章:
延遲效果|Delay Category
延遲時長應用 | Delay Time

通常我會在solo的部分加入Delay(延遲)效果。 如果我想要聲音更有空間感,我會加入Reverb(混響)。 而對於Reverb(混響)效果來說也是一樣的,針對混響的音色與decay(衰減)來使用是一種進階的技巧,這裡我不會去談論。 如果你對這個話題感興趣的話,請參考我之前的文章:
創建你的三維音色 | Build Your Sound in 3 Dimensions

Delays, there are various types, and it's an advanced skill to use delays related to the sound characteristics and delay time. I won't talk about it here, if you are interested in this topic, please visit my previous posts:
延遲效果|Delay Category
延遲時長應用 | Delay Time

Usually, I add the delay for the solo part. If I want the sound has more room or space, I will add reverb to it. Same as Reverb, it's also an advanced skill to use the reverbs related to the sound characteristics and decay time. I won't talk about it here, if you are interested in this topic, please visit my previous post:
創建你的三維音色 | Build Your Sound in 3 Dimensions


最後一步: 調平Preset的音量。
Mghty Lite BT MKII提供了Patch Level 推子,你可以通過他來調整Preset的整體音量。
事實上我不會去用他,如果你正確地依照『調整音色』步驟,那你將用不到他。
對我來說,他是備而不用。

The final step: Re-Level the Preset.
In the Mighty Lite BT MKII, you can adjust the overall Preset volume through the Patch Level slider. Actually, I don't use it, if you follow the TONE TWEAKING steps correctly, you won't need it. For me, it's just in case.

Bon Jovi - Always - Electric Guitar Cover by Kfir Ochaion - NUX Mighty Lite BT MKII


Recording | 錄音


到『系統偏好設定』去設置『聲音』。 將NUX NGA-3BT設為『輸入』及『輸出』裝置。

Go to System Preferences to set up the Sound. Choose NUX NGA-3BT as Input & Output.

開啟DAW(這裡示範的是Logic Pro),並到Preferences設定Audio的 I/O Buffer Size為 128 Samples。

Open the DAW (Logic Pro), and go to Preferences to set up I/O Buffer Size as 128 Samples.




利用Logic Pro內建的Drummer Track來製作鼓音軌,這時候就可以錄製貝斯啦。
Logic Pro很適合像我這種對MIDI不熟悉的人,因為只需要打開鼓手音軌,挑選喜愛的曲風,挑選鼓具,聽一下節奏並調適一下就可以開始錄製了。

Open Logic Pro's Drummer Track to make the drum track, then you can record the bass.
Logic Pro is very friendly to me, I am not familiar with MIDI. I just open the Drummer Track, choose the style, drum kits, and listen to the track to tweak. Then I can start recording.

於是我開始錄製『貝斯』、『節奏吉他』、『Solo』。

So I start to record "Bass", "Rythm Guitar", and "Solo Track".


錄音時,你可以通過 Mighty Editor™ 編輯軟體來設置USB Routing,一般我們會選擇『Normal』,也就是『錄製你所聽到的聲音』。

For recording, you can set up the USB Routing through Mighty Editor™ editor (PC/MAC). Regularly we will choose "Normal" to record "What you heard" onto DAW.



如果你要『Reamp』的話,那首先你要先錄製『Dry Signal』到DAW裡,所以先在USB Routing設置為『Dry Out』,這時候你聽到的是『Processed Signal』,可是錄製上去的是『Dry Signal』。

If you want to "Reamp", firstly you have to record "Dry Signal" onto DAW. So set up USB Routing as "Dry Out", then what you heard is "Processed Signal", but what is recorded onto DAW is "Dry Signal".




此時就可以利用錄製好的『Dry Track』來操作『Reamp』了。 先到Mighty Editor™ 編輯軟體來設置USB Routing為『Reamp』。

Now you can use the "Dry Track" to operate "Reamp". Go to Mighty Editor™ editor to set up USB Routing as "Reamp".



在DAW裡,將剛剛錄製的『Dry Track』設為『Solo播放』,在等等錄音時就只會播放該音軌,其他音軌將會Mute。 這時候就可以錄製『Reamp音軌』了。 (我在DAW裡標示為WET1)

Set up the "Dry" track as "Solo Playing" in the DAW, then while you record, the DAW will only play the "Dry" track, others will be mute. Then you can record the "Reamp" track. (I named the "Reamp" track as "WET1".)

註記: MIGHTY LITE BT MKII的『Loopback』可以將電腦端播放的背景一起錄製起來,但是不包含『AUX IN』及『藍牙音頻』。

Note: The "Loopback" USB Routing in MIGHTY LITE BT MKII can record the playback from PC/MAC, but not includes "AUX IN" & "Bluetooth Audio".



如果你對這個小鋼炮感興趣,請至 ➫
https://www.monkcustom.com/ecommerce/nux/%E9%9F%B3%E7%AE%B1/nux-mighty-lite-bt-mkii.html

Is this the Best Mini Desktop Amp Ever Made?

感蝦支持~



2023年6月23日 星期五

Modeler vs Profiler ?! |NUX AMP ACADEMY vs IK TONE X

Modeler vs Profiler ?! 

NUX AMP ACADEMY vs IK TONE X


Stomp-box Modeler


之前我們在2022年3月份,寫過一篇橫向對比的Stomp-box Modeler,介紹了市面上常見的產品,如NUX Amp Academy、Strymon Iridium、Walrus ACS1、Atomic Ampli-Firebox、BOSS IR-200等等。

Previously, in March 2022, we wrote an article on the Stomp-box Modeler comparison, introducing common products on the market, such as NUX Amp Academy, Strymon Iridium, Walrus ACS1, Atomic Ampli-Firebox, BOSS IR-200, etc.



而主打Plug-In軟體的IK Multimedia也在AmpliTube的基礎上,推出Stomp-box Modeler: TONE X。 TONE X採用的算法是類似QC的AI建模,源自跟KEMPER系出同門的『黑盒算法』。

IK Multimedia, which mainly focuses on Plug-In software, also launched the Stomp-box Modeler: TONE X on the basis of AmpliTube. The algorithm adopted by TONE X is an AI modeling similar to QC, which is derived from the "Black Box Algorithm" of the same family as KEMPER.

註:關於Amp Modeling的技術與IR的觀念介紹,請見:

Note: For the introduction of Amp Modeling technology and IR concepts, please see:



IK TONE X vs NUX Amp Academy

理解大家沒有耐心看一堆文字敘述,所以我們直接上主菜,音色對比。
這邊我們挑選幾個有共同音箱模型的Reference來做對比。(搭載一樣的IR檔。)

I understand that everyone has no patience to read a bunch of text descriptions, so we go straight to the main course and compare the sound.
Here we select a few references with the same Amp Models for comparison. (Equipped with the same IRs.)

1. IK ToneX vs NUX Amp Academy | JCM800 

2. IK ToneX vs NUX Amp Academy | Super Reverb

3. IK ToneX vs NUX Amp Academy | Twin Reverb


Amp Modeling & IR

在說明Modeler與Profiler之前,我們先來講述一下Amp Modeling跟IR之間的區別,我發現有許多人對於這兩者之間的定義有所混淆。

我們在中文說到的『音箱模擬』指的就是『Amp Modeling』,也就是針對『音箱』來做建模的動作。後面我們會講述到Modeling的方法。

Before explaining Modeler and Profiler, let's talk about the difference between Amp Modeling and IR. I found that many people are confused about the definition of the two.

The "Amp Simulation" we mentioned in Mandarin refers to "Amp Modeling", which is the action of modeling for an "Amplifier". We will talk about the Modeling method later.

(由上圖可知IR所還原的就是『麥克風收取箱體(喇叭)』的聲音。 
From the picture above, it can be seen that what IR restores are the sound of "Micing the Cabinet (speaker)".)


而IR其實是近幾年用來實現Cab Sim的一種方法,在之前的文章有提到過,近年因為DSP運算力上來了,所以早期採用濾波器做Cab Sim的方法就改由IR卷積取代了。 所以IR指的是『箱體模擬』,並非『音箱模擬』。

IR is actually a method used to realize Cab Sim in recent years. As mentioned in the previous article, in recent years, due to the increase in DSP computing power, the early method of using filters to do Cab Sim has been replaced by IR convolution. So IR refers to "Cabinet Simulation", not "Amp Simulation".


Amp Modeling: Modeler & Profiler

音箱模擬,顧名思義就是要去『模擬』音箱,那麼我們得先來看一下,我們要去模擬什麼樣的音箱。

Amp Simulation, as the name suggests, is to "simulate" amplifiers, so we have to take a look at what kind of amps we want to simulate.

首先我們理解到我們要模擬的對象『Electric Guitar Amps』有很重要的特性,那就是帶有『失真』信號。即使是我們認為的Cleanish類別音箱,其實相較於Acoustic Guitar Amp 或者 PA系統,還是帶有失真特性。

First of all, we understand that the object we want to simulate, "Electric Guitar Amps", has a very important characteristic, that is, it has a "distortion" signal. Even what we think of as a cleanish category amp has distortion characteristics compared to an Acoustic Guitar Amp or PA system.

而我們所說的Electric Guitar Amp往往指的就是Tube Amp。 因為吉他手們喜愛真空管音箱那“溫暖且肥厚的音色”以及“充滿生命力的失真”。

And what we call Electric Guitar Amp often refers to Tube Amp. Because guitarists love the "warm, fat tone" and "organic distortion" of tube amps.



而電吉他音箱主要形成音色的部分在前端的PRE-AMP,這部分也是主要失真特性的來源。 所以在Digitech 、Zoom、Line 6這三個經典綜效老牌(2005~2010主力綜效品牌)在當時半導體行業發展下,採取了『Waveshaper』的建模方式。 這種建模方式的好處是,工程師不用理解真空管電路的工作原理。(小編為1983年生,在大學時期的Smith電子學聖經本早就沒有“真空管”了,當時電子行業也早已經是半導體為主流了。)

The main part of the electric guitar amplifier to form the tone is the PRE-AMP, which is also the source of the main distortion characteristics. Therefore, Digitech, Zoom, and Line 6, the three classic brands (main brands from 2005 to 2010), adopted the "Waveshaper" modeling method during the development of the semiconductor industry at that time. The advantage of this approach to modeling is that engineers don't have to understand how vacuum tube circuits work. (I was born in 1983. When I studied at university, the Smith Electronics textbook had no "vacuum tubes". At that time, the electronics industry was already dominated by semiconductors.)

這是Preamp的最後一級,旨在驅動效果環路,也是第一個出現失真的Preamp級。 該設計類似於 Mesa Boogie MK I 中的Preamp失真級。

陰極電阻器被完全旁路,以防止負反饋降低三極管電路的豐富非線性行為。 R1 和 R2 形成分壓器,以將大約 100V 峰值的最大板電壓擺幅降低到大約半伏峰值的最大影響發送擺幅。

根據 12AX7 計算器,柵極偏壓在非常溫暖的 -1V。

This is the final stage of a preamp designed to drive an effects loop and is the first preamp stage to break into distortion. The design is similar to the preamp distortion stage in the Mesa Boogie MK I.
The cathode resistor is fully bypassed to prevent negative feedback from reducing the triode circuit's lush nonlinear behavior. R1 and R2 form a voltage divider to reduce a maximum plate voltage swing of about 100V peak to a maximum effect send swing of about half a volt peak.
According to the 12AX7 Calculator, the grid is biased at a very warm -1V.

隨著輸入信號的增加,上游電阻網絡上的電網電流的影響會壓縮正向電網電壓擺幅。 輸入信號的負擺幅不受限制。 嚴重的不對稱性會產生大量的二次諧波失真,這種失真會提前達到穩定狀態並持續到負電網電壓擺幅達到大約 -3V。 此時,峰峰值板電壓擺幅幾乎達到極限。

當負柵極電壓擺幅超過-3.5V時,正極板電壓擺幅從溫和壓縮轉變為急劇削波。 輸出波形變得更加對稱,三次諧波失真開始占主導地位。 超過該點,輸出信號達到最大值 - 它無法響應輸入信號幅度的進一步增加。

As the input signal level increases, positive grid voltage swings are compressed by the effects of grid current on the upstream resistor network. Negative swings of the input signal run free. The severe asymmetry produces bucketloads of 2nd-harmonic distortion that plateaus early and lasts until negative grid voltage swings reach approximately -3V. At that point, the peak-to-peak plate voltage swing has almost reached its limits.

When negative grid voltage swings exceed -3.5V, positive plate voltage swings transition from mild compression to sharp clipping. The output waveform becomes more symmetrical and 3rd-harmonic distortion begins to dominate. Beyond that point the output signal is at its maximum - it cannot respond to further increases in input signal amplitude.


Traditional Waveshapers (Waveshaper Modeler)

傳統上,電吉他音箱的非線性行為是通過『Waveshaper』來建模的,它將輸出描述為輸入的函數。 例如,這是 Line 6 專利中包含的『波形整形器』(Waveshaper)。

Electric guitar amp nonlinear behavior has traditionally been modeled by a 『Waveshaper』, which describes the output as a function of the input. Here, for example, is a waveshaper included in a Line 6 patent.

對於線性電路,傳遞函數是一條直線。 Line 6 Waveshaper在正負輸入擺幅的極端情況下顯示壓縮。 它還描繪了不對稱失真,因為正電壓擺幅的曲線不是負擺幅曲線的鏡像。

For a linear circuit, the transfer function is a straight line. The Line 6 Waveshaper shows compression at the extremes of positive and negative input swings. It also depicts asymmetric distortion, because the curve for positive voltage swings is not the mirror image of the curve for negative swings.

聊到這裡,估計非工科的朋友已經暈倒了,所以我們就此打住,關於Waveshaper建模,後期有更多改進方法如“採用高通濾波器來捕捉耦合電容器 CG 的低頻行為“。
以及 “Cubic Spline Interpolation of the Transfer Function“、” A Digital High-Pass Filter to Emulate the Coupling Capacitor“ 等作法。

It is estimated that non-engineering friends have fainted, so let's stop here. Regarding Waveshaper modeling, there were more improvement methods in the later stage, such as " A high-pass filter that captures the low-frequency behavior of coupling capacitor CG".
And “Cubic Spline Interpolation of the Transfer Function“, ”A Digital High-Pass Filter to Emulate the Coupling Capacitor“, …etc.


The origin of Modeler

在2000年時,Line 6發表PDO,由於主打Amp Modeling的概念,從此綜合效果器就有了新的名詞定義~Modeler。

In 2000, Line 6 released PDO. Because of the concept of Amp Modeling, multi-effects has a new definition of the term ~Modeler.

Black Box & White Box 


2007年,Fractal Audio發表Axe-Fx,採用ADI的SHARC,運算力足夠實現『IR卷積』以及『白盒算法』。
2010年,Kemper發表Profiler,採用『黑盒算法』建模。(讓我們稱之為Profiling。)

In 2007, Fractal Audio released Axe-Fx, using ADI's SHARC, the computing power is enough to realize "IR convolution" and "white-box algorithm".
In 2010, Kemper released Profiler, which uses the "black-box algorithm" to do modeling. (Let's call it Profiling.)

Black-Box

https://en.wikipedia.org/wiki/Black-box_testing

黑盒算法建立的基礎在於系統自身信息不可知,而在只有輸入輸出關係的情況下獲得系統的傳遞特性的方法。
一般來說,工程師不需要程式代碼應用、內部結構和編程知識的具體知識。 測試人員知道軟體應該做什麼,但不知道它是如何做的。 例如,測試人員知道特定的輸入返回特定的、不變的輸出,但不知道軟體首先如何產生輸出。

Specific knowledge of the application's code, internal structure, and programming knowledge. In general, is not required. The tester is aware of what the software is supposed to do but is not aware of how it does it. For instance, the tester is aware that a particular input returns a certain, invariable output but is not aware of how the software produces the output in the first place.


黑盒算法是在對實體音箱或者效果器的內部結構未知的前提下,憑藉信號輸入/輸出的關係來猜測整個機器的工作狀態,當猜測的正確率達到一定程度時(例如高於98%)即認為實現這個音箱的音色。

黑盒算法的優勢是結構簡單,對運算力的要求不高,一般來說黑盒算法使用簡單的通用結構來實現音色的模擬。在相同的算力下黑盒算法通常可以獲得不錯的精度。他的主要缺點在於無法應對系統內部機構變化時的音色實時改變。例如,音箱和效果器都有音量,高中低音,增益等調節旋鈕,在黑盒算法建立模型的時候需要固定上述旋鈕於一個位置,然後測試信號的輸入輸出特性,求得模型的參數。一旦旋鈕的位置變化了,這個模型應對新系統的關係也就不成立了。所以這個方法適合作為一種拍照方法,把當前音箱的音色固定的採集下來使用。

The black-box algorithm is to guess the working status of the whole machine by virtue of the signal input/output relationship without knowing the internal structure of the physical amplifier or effector. When the correct rate of guessing reaches a certain level (for example, higher than 98%) That is to say, the sound of this amplifier is realized.

The advantage of the black-box algorithm is that it has a simple structure and does not require high computing power. Generally speaking, the black-box algorithm uses a simple general-purpose structure to realize the simulation of sound. Under the same computing power, black-box algorithms can usually obtain good accuracy. His main shortcoming is that it cannot cope with the real-time change of tone when the internal mechanism of the system changes. For example, amplifiers and effectors have adjustment knobs such as volume, high, mid, bass, gain, ...etc. When profiling a model with the black-box algorithm, the above knobs need to be fixed at one position, and then the input and output characteristics of the signal are tested to obtain the parameters of the model. Once the position of the knob is changed, the relationship of the model to the new system does not hold. Therefore, this method is suitable as a method of taking pictures, and the sound of the current amplifier is fixed to use.

White-Box


白盒算法就是打開一台設備的外殼,看裡面用了什麼元件,元件怎麼連接的,然後用一套數學方程來實現整個機器的工作狀態。

白盒測試的基本過程要求測試人員對被測試的源代碼有深入的了解。 程式員必須對應用程式有深入的了解,才能知道要創建什麼類型的測試用例,以便運用每一條可見的路徑進行測試。 一旦理解了源代碼,就可以對其進行分析以創建測試用例。

The white-box algorithm is to open the shell of a device to see what components are used inside and how the components are connected and then uses a set of mathematical equations to realize the working state of the entire machine.

White-box testing's basic procedures require the tester to have an in-depth knowledge of the source code being tested. The programmer must have a deep understanding of the application to know what kinds of test cases to create so that every visible path is exercised for testing. Once the source code is understood then it can be analyzed for test cases to be created.


在選擇建立虛擬設備時首先要確定使用什麼物理系統作為基本的條件約束,對於電子網絡來說僅需遵循牛頓定律,和克希霍夫電壓、電流定律即可:

When choosing to build a virtual device, you must first determine what physical system to use as the basic conditional constraint. For electronic networks, you only need to follow Newton's law and Kirchhoff's voltage and current laws:


上述定律可滿足一般阻容電路網絡的表述,如果需要引入磁場元件諸如變壓器,電感線圈等元件還可引入法拉第電磁定律:

The above laws can satisfy the expression of the general resistance-capacitance circuit network. If it is necessary to introduce magnetic field components such as transformers and inductance coils, Faraday’s electromagnetic law can also be introduced:

通過上面的四個定律可以描述任意複雜的電路拓撲,由於這這種對系統的表述方式不摻雜任何人為的影響,可獲取十分自然的信號響應,這正是白盒算法的魅力所在。
下面我們通過兩個例子來解釋如何實現上述系統求解,下圖是一個經典的話放EQ的中頻電路,電路包含電阻、電容、電感三種線性元器件:

Arbitrarily complex circuit topologies can be described through the above four laws. Since this way of expressing the system does not involve any artificial influence, a very natural signal response can be obtained, which is the charm of the white box algorithm.
Below we use two examples to explain how to solve the above system. The figure below is a classic circuit for mic preamp mid-EQ. The circuit includes three linear components: resistors, capacitors, and inductors:


我知道,到此已經很難再講下去了,我們直接說白盒算法的特點。

白盒算法的優勢是可以完全的反映模擬設備的所有特性,包括設備的調節旋鈕,電源,溫度等參數對音色的影響等。他還可實現和模擬設備相同的動態反映(樂手所說的手感)和高度逼真的音色。

他的主要缺點是:
1. 要為每一個類比元件建立單獨的數學模型,例如:電子管,晶體管,運算放大器,電阻,電容,電感,變壓器等元件,以及類比元件的電路是如何連接的,因此工作量十分巨大。
2. 需要設計者俱有非常深層次的類比電路設計理論知識才能重現原型機的音色。 
3. 需要大量的DSP算力來達到模型的高精確度。

I know it's hard to go on here, let's just talk about the characteristics of the white-box algorithm.

The advantage of the white-box algorithm is that it can completely reflect all the characteristics of the simulated equipment, including the adjustment knob of the equipment, the influence of parameters such as power supply and temperature on the sound, etc. It also achieves the same dynamic response (what players call playability) and highly realistic tone as simulated equipment. 

The main disadvantages are:
1. It is necessary to establish a separate mathematical model for each analog device, such as tubes, transistors, operational amplifiers, resistors, capacitors, inductors, transformers, and other components, as well as how the circuits of the analog devices are connected, so the workload is huge.
2. It is necessary for the designer to have a very deep theoretical knowledge of analog and electrical design in order to reproduce the sound of the prototype.
3. A large amount of DSP computing power is required to achieve high accuracy of the model.

上面的圖片就是NUX品牌採用『白盒算法』建模的程式網路結構。

The picture above is the program mesh structure modeled by the NUX brand using the "white-box algorithm".


The definition of Modeler & Profiler

由前面的介紹,我們可以了解Amp Modeler可分為 Modeler與Profiler。 這邊我們再補充一個新的做法,那就是『AI類神經網路』。

2020年,Neural DSP發表Quad Cortex,採用的就是AI算法,AI算法是基於『黑盒算法』的延伸,一樣無需知道系統內容,量測輸入、輸出信號的關係。 AI在於,不需要測試人員進行測試,而是自主測試,並且根據假設的系統方程進行訓練來獲得最逼近reference輸出結果的方程式。

From the previous introduction, we can understand that Amp Modeler can be divided into Modeler and Profiler. Here we add a new approach, which is "AI neural network".

In 2020, Neural DSP released Quad Cortex, which uses the AI algorithm. The AI algorithm is an extension based on the "black-box algorithm". It also does not need to know the system content to measure the relationship between input and output signals. AI lies in the fact that testers are not required to test, but are tested independently, and trained according to the assumed system equations to obtain the equations that are closest to the reference output results.

而最近IK所推出的TONE X也是基於AI。(IK稱為MACHINE MODELING。)

The TONE X recently launched by IK is also based on AI. (IK named it MACHINE MODELING.)

總結上述,Amp Modeler分為Modeler與Profiler,其中Modeler的技術又分成Waveshaper與White-box。 Profiler的技術分為Black-box與AI。

To sum up the above, Amp Modeler is divided into Modeler and Profiler, and the technology of the Modeler is divided into Waveshaper and White-box. Profiler technology is divided into Black-box and AI.


1. Waveshaper Modeler: 如LINE6、 ZOOM、 Strymon Iridium、 Walrus ACS-1、 BOSS IR-200, …etc.

採用Waveshaper的考量是,工程師不需要具備真空管電路數學模型的知識背景與工作原理,建立的Amp Model數學模型較簡單,不耗費DSP運算力。 
但缺點就是無法還原真空管音箱的負反饋與動態響應,進而影響手感。 最明顯的就是當你外接『過載效果器』時,聲音會被壓縮,縮掉。無法像真實音箱承受大信號。

The reason for using Waveshaper is that engineers do not need to have the knowledge background and working principle of the vacuum tube circuit mathematical model. The Amp Model mathematical model established is relatively simple and does not consume DSP computing power. 
But the disadvantage is that it cannot restore the negative feedback and dynamic response of vacuum tube amplifiers, which will affect the playability. The most obvious thing is that when you connect an "Overdrive pedal" externally, the sound will be compressed and shrunk. It cannot withstand large signals like real tube amplifiers.


2. White-box Modeler: 如Fractal、 NUX。

如前面所提到,白盒算法考驗著工程師要對系統(也就是真空管音箱電路)有高度的知識背景,且Programmer也要理解系統物理建模的數學模型。 再者每一層級的電路都需要進行量測校正,所以需要拆解原型機來做驗證,建模的過程相當耗時。
但對樂手來說,最重要的是White-box是可以最接近真空管音箱的『手感反饋』與『過載信號承受性』,以及轉動EQ旋鈕時的『混沌現象』。

As mentioned earlier, the white-box algorithm tests that the engineer must have a high degree of knowledge background on the system (that is, the tube amplifier circuit), and the Programmer must also understand the mathematical model of the physical modeling of the system. In addition, the circuits at each level need to be measured and corrected, so the reference needs to be disassembled for verification, and the modeling process is quite time-consuming.
But for musicians, the most important thing is that White-box is the closest to the "playability feedback" and "overdrive signal tolerance" of tube amplifiers, as well as the "chaos phenomenon" when turning the EQ knob.


3. Black-box Profiler: 如Kemper、 Mooer。

建模速度快,所以品牌方或者第三方,都可以進行Profiling,並且分享Profile檔案。(Amp Model) 但Profile缺點就是靜態參數,當你轉動EQ時,會跟reference有所差異,且你會發現雖然整體頻響跟原型機很像,但是彈奏手感都是定型的,即使你換了不同Amp Model。 當你外接過載效果器時,聲音也會產生不自然的壓縮。

The modeling process is fast, so the brand or the third party can perform Profiling and share the Profile file often. (Amp Model) 
But the disadvantage of Profile is the static parameters. When you turn the EQ, it will be different from the reference, and you will find that although the overall frequency response is similar to the reference, the playability is fixed, even if you change to different amp models. When you plug in an overdrive, the sound will be unnaturally compressed.


4. AI Profiler: 如Neural QC、 IK ToneX。

建模速度最快,其內建通用模型,AI自主訓練擬合曲線方程,Profile的過程較傳統黑盒子簡單。 整體頻率響應可以比傳統Profiler精準,但目前的AI Profiling時間還是相當長,如Neural QC約要40分鐘,一般用戶還是很少使用這個功能。 另外跟黑盒子算法一樣的缺點:彈奏手感都是定型的,即使你換了不同Amp Model。 當你外接過載效果器時,聲音也會產生不自然的壓縮。

The modeling speed is the fastest, its built-in general model, AI self-training fitting curve equation, and the process of Profile is simpler than a traditional black box. The overall frequency response can be more accurate than the traditional profiler. 
But the current AI profiling time is still quite long, for example, Neural QC takes about 40 minutes, and ordinary users still rarely use this function. 
In addition, the same disadvantage as the black box algorithm: the playability is fixed, even if you change to a different Amp Model. When you plug in an overdrive, the sound will also be unnaturally compressed.


Conclusion & My 2 cents

現代吉他手選擇Modeler的機會越來越高,因為演出時遇到Amp-less(無音箱)的場景越來越多。 喜歡單顆效果器組盤的吉他手會選擇Stomp-box Modeler類型來搭配自己喜愛的單顆效果器,尤其是『Overdrive』與『Distortion』。
 
The chances of modern guitarists choosing Modeler are getting higher and higher because there are more and more Amp-less (no speaker) scenes during performances. Guitarists who like effect pedals will choose the Stomp-box Modeler type to match their favorite effectors, especially "Overdrive" and "Distortion".

所以,如果你的考量是以live gigs為主,那麼挑選『白盒算法』為基底的NUX Amp Academy 將會是一個好選擇。 如前所述,『白盒算法』擁有近似真空管音箱的『Negative Feedback』、『良好的彈奏手感反饋』、『優異的動態範圍』、『過載效果信號承受性』。 
此外產品本身帶有可獨立切換IR開關的XLR輸出及1/4”(6.35mm)輸出,搭配OTG可以在現場使用手機進行深度調參,Send/Return外接post efx。 
但缺點是沒有傳統MIDI口或者3.5mm MIDI口,如果要使用MIDI踏板的話還需要使用帶有USB HOST的MIDI控制器。

If your consideration is based on live gigs, then choosing NUX Amp Academy based on the "White-box Algorithm" will be a good choice. As mentioned above, the "White-box Algorithm" has "Negative Feedback" similar to vacuum tube amplifiers, "good playability feedback", "excellent dynamic range", and "overdrive signal tolerance". 
In addition, the product itself has an XLR output and a 1/4” (6.35mm) output that can independently switch the IR on/off. With OTG, you can use your mobile phone for in-depth parameter adjustment. Send/Return is connected to an external post effector. 
But the disadvantage is that there is no traditional MIDI port or 3.5mm MIDI port, if you want to use MIDI pedals, you need to use a MIDI controller with USB HOST.




反之,如果你以家裡宅錄為主,希望有比較多的Amp Model,或者第三方做好的音色預設,那麼Profiler會是你的選擇。 畢竟宅錄,對於手感上的要求度會低一些,且錄進去後使用DAW外掛其他效果來修飾音軌是很常見的使用場景,就無須考慮『過載效果信號承受性』。且Profiler聽覺上更像『成音』的音色。(像是唱片裡錄製好的吉他音色。) 

而最近市場上討論度最高的平價Profiler,當屬IK ToneX。 小編的使用體驗上,覺得可惜的部分就是編輯預設的介面跟邏輯跟一般的綜合效果器差異很大。 機器本身只有LED屏,顯示的信息量少,現場調參不友善。 此外沒有Send/Return來外接post efx。 如果你要Capture其他reference的話,還需要另購ToneX Capture。

註記:如果你已經買了IK ToneX,對於編輯音色不太熟悉,可以參考這個教學影片。

If you mainly do home recording and hope to have more Amp Models or presets(patches) made by third parties, then Profiler will be your choice. Home recording has lower requirements on playability and it is a very common usage scenario to use DAW plug-in effects to modify the audio track after recording, so there is no need to consider the "overdrive signal tolerance". And the Profiler sounds more like a "processed sound". (Like the guitar sound recorded on a record.) 

The most discussed affordable Profiler on the market recently is IK ToneX. In the editor's experience, the regrettable part is that the interface and logic of editing presets are very different from those of general multi-efx devices. The machine itself only has an LED screen, which displays little information, and the parameter adjustment is not friendly. In addition, there is no Send/Return to external post-efx. If you want to capture other references, you need to purchase ToneX Capture separately.

Note: If you have bought IK ToneX and are not familiar with editing tones, you can refer to this tutorial video.





回顧一下,我所謂的『過載信號兼容性』

Recall, what I call "Overdrive Signal Compatibility".


IK ToneX vs NUX Amp Academy | Twin Reverb

IK ToneX vs NUX Amp Academy | Super Reverb


IK ToneX vs NUX Amp Academy | JCM800

Neural Quad Cortex vs NUX Amp Academy

NUX Amp Academy vs LINE6 HX STOMP | Fender Twin Rvb & Friedman BE-100

Strymon Iridium VS NUX Amp Academy | Drive Pedal Headroom & Response Test

相信聽完以上的對比後,大家應該更理解我所謂的『彈奏手感 Playability』、『動態範圍 Dynamic Range』、『過載信號兼容性 Overdrive Signal Compatibility』。

青菜蘿蔔各有所好,愛其所擇,擇其所愛~ 錢沒有不見,只是變成你喜歡的樣子!

I believe that after listening to the above comparison, you should understand what I call "Playability", "Dynamic Range", and "Overdrive Signal Compatibility".

Vegetables and radishes have their own preferences, love what you choose, choose what you love ~ the money is not gone, it just becomes what you like!

結尾附上小彩蛋~ IK TONEX與NUX AMP ACADEMY個別的耗電量: